Customer Reviews for Timney Timney Triggers Ruger 77-22 Sear and Spring Kit

This product is no longer available. Continue shopping at Cabela's.

Timney Timney Triggers Ruger 77-22 Sear and Spring Kit

Improve your accuracy with the 77-22 Sear Spring Kit. Delivers a crisp, light, trigger pull.
Overall Customer Rating:
4.4 out of 5
4.4
 out of 
5
(5 Reviews) 5
Open Ratings Snapshot
Rating breakdown 5 reviews
5 Stars
3
4 Stars
1
3 Stars
1
2 Stars
0
1 Star
0
5 out of 5(100%)reviewers would recommend this product to a friend.
Customer Reviews for Timney Triggers Ruger 77-22 Sear and Spring Kit
Review 1 for Timney Triggers Ruger 77-22 Sear and Spring Kit
Overall Customer Rating: 
5 out of 5
5 out of 5
Country: United States
State: Alaska
Age: 26-35
Gender: Male
Would you recommend this product to a friend? Yes

very nice and easy to install

Date:May 30, 2012
great buy and cheap price.
0points
0out of 0found this review helpful.
Review 2 for Timney Triggers Ruger 77-22 Sear and Spring Kit
Overall Customer Rating: 
5 out of 5
5 out of 5
Location: collegeville, PA
Age: 26-35
Gender: Male
Would you recommend this product to a friend? Yes

Timney trigger ruger 77- 22 sear and springkit

Date:September 26, 2011
This trigger kit was great. It took about 20 min to install and turned my nine lbs pull into a crisp and smooth 3.6 lbs. You just have to be cairfull not to take of to much when you file down the safety catch.
0points
0out of 0found this review helpful.
Review 3 for Timney Triggers Ruger 77-22 Sear and Spring Kit
Overall Customer Rating: 
5 out of 5
5 out of 5
Location: Utah
Would you recommend this product to a friend? Yes

Good Product

Date:January 31, 2010
I installed this in my 77/17 last night. If it weren't for the filing of the trigger to allow the safety to work, this would take about 10 minutes to install. Since I didn't want to screw it up, I filed very small amounts until it was just right, and the job took closer to an hour, but it really was very easy, it just takes a lot of careful filing, and trying it often to make sure you stop when it's just right. I had the benefit of disassembly instructions for my 77/17, which made it very clear. Too bad pictures are not included in Timney's instructions. The end result is a nice light trigger, with still a bit of creep but I think it'll smooth up after a bit of use. I'm totally satisfied. WAY better than the horrible factory trigger. Now to do my 10/22....
0points
0out of 0found this review helpful.
Review 4 for Timney Triggers Ruger 77-22 Sear and Spring Kit
Overall Customer Rating: 
3 out of 5
3 out of 5
Location: IA
Would you recommend this product to a friend? Yes

Better than before but not 2.5 lbs

Date:November 20, 2009
Replaced sear and spring on Ruger 77/17 HMR with this kit. It came with instructions but there were no photos. It really was not very difficult to follow even without any photos. For my gun it took quite a bit of filing to get the safety to engage. Because you frequently have to check to see if you've filed enough by reinstalling the trigger it did take a while, maybe 45 minutes to get the filing done. I didn't measure the trigger before but afterwards I hung lead weights on the trigger until it fired and is like 3.5-4 lbs. Better than before but not the 2.5 lbs it says on the package. If you need way lite trigger pull, then you better replace with an adjustable trigger and not just a new spring/sear.
0points
0out of 0found this review helpful.
Review 5 for Timney Triggers Ruger 77-22 Sear and Spring Kit
Overall Customer Rating: 
4 out of 5
4 out of 5
Would you recommend this product to a friend? Yes

Timney Triggers 77/22 sear and spring convresion

Date:August 8, 2009
INSTANT RELIEF! This conversion took literally 3 minutes to install. The filing took a little longer, but it was easily accomplished with a small flat file. My 77/22's trigger was so tight I could lift it off of the ground with the trigger before it would snap. Now I have a crisp 2 1/2 pound pull. I can't believe the difference.
0points
0out of 0found this review helpful.